×

Notice

The forum is in read only mode.
  1. Forum
  3. Public Forums
  5. Salomé & Pre-processing
  7. can anybody make 2d shell tutorial?

can anybody make 2d shell tutorial?

  • Bridge_PL
  • Topic Author
  • Offline
  • New Member
  • New Member
More
14 years 7 months ago #3918 by Bridge_PL
Replied by Bridge_PL on topic Re:can anybody make 2d shell tutorial?
Hello again Kees, :side:

Yes, You are right I forgot line between P6 and P8 in file I attached to forum.

I'm beginner in CAE, and I'm not good enought to make tutorial myself, so tutorial should be signed by more advanced user.
I am glad to co-operate with you in this tutorial.

I make more geometry:
- I add line between P6 and P8,
- create faces for each presure field,

what more should I do with geometry? :woohoo:

Regards,

This weekend will be with CAE :silly:

Attachment geometry_002.zip not found

Attachments:
More
14 years 7 months ago #3922 by kwou
Replied by kwou on topic Re:can anybody make 2d shell tutorial?
Hoi Bridge

please have a look at the hdf file and give your command.
Later on I will give some explanation - too late now.

kind regards - kees

Attachment shell_partition.zip not found

Interest: structural mechanics, solar energy (picture at 'my location' shows too little pv panels)

--
kind regards - kees
Attachments:
More
14 years 7 months ago #3925 by kwou
Replied by kwou on topic Re:can anybody make 2d shell tutorial?
may be erased ....<br /><br />Post edited by: Kees Wouters, at: 2010/03/06 12:22
Interest: structural mechanics, solar energy (picture at 'my location' shows too little pv panels)

--
kind regards - kees
Attachments:
  • Bridge_PL
  • Topic Author
  • Offline
  • New Member
  • New Member
More
14 years 7 months ago #3926 by Bridge_PL
Replied by Bridge_PL on topic Re:can anybody make 2d shell tutorial?
Hi Kees,

I have looked at your's file.
You have very interesting idea,
create single face with partitions for each presure. :side:

I was trying to make single face for each presure,
what couses more problems than your idea.

Which comand you used to create Fbot,Fcentre1,Fcentre2,Ftop,Fmain from Part_main?

I try Explode to Faces, but i get icon with one square, your's icons are two squares.

I think, We need two groups of edges for fixed boundary conditions.

Regards
More
14 years 7 months ago #3927 by kwou
Replied by kwou on topic Re:can anybody make 2d shell tutorial?
Hoi Bridge,

I updated some files.

The hdf, comm, astk/export files now function make it possible to run Code Aster. You need to make quadratic mesh in Salome and export the mesh file to mesh.med or alike. The displacements, local and equivalent stresses are determined.

It is probably best to try to start and mention all the problems and worries you have and come across. Write them all in a wiki and extend to calculations later on.

Have fun.

Kind regards - kees

Attachment shell_partition_2.zip not found

Interest: structural mechanics, solar energy (picture at 'my location' shows too little pv panels)

--
kind regards - kees
Attachments:
  • Bridge_PL
  • Topic Author
  • Offline
  • New Member
  • New Member
More
14 years 7 months ago #3928 by Bridge_PL
Replied by Bridge_PL on topic Re:can anybody make 2d shell tutorial?
I analized your's file all morning :cheer:
I added fixed-1 and fixed-2 groups for boundary conditions.
;)

Attachment Study_face_partition_02.zip not found

Attachments:
Moderators: catux
  1. Forum
  3. Public Forums
  5. Salomé & Pre-processing
  7. can anybody make 2d shell tutorial?
Time to create page: 0.166 seconds
Powered by Kunena Forum